EMS/TENS Devices

Diameter: 25MM
Length: 145MM
With 2MM PIGAIL connection

The EV-906 Digital TENS/EMS is a battery operated pulse generator that sends electrical impulses electrodes to the body and reach the nerves and underlying muscle group. This unit is a combination stimulator of TENS and EMS which can be used for muscle stimulation and pain relief. The device is provided with four controllable output channels, each independent of each other. An electrode pair can be connected to each output channel. The intensity level is controlled by press buttons.      MECHANISM TECHICAL DESCRIPTION 01 Channel Four, isolated between channels 02 Pulse Amplitude Adjustable, 0-100 mA peak into 500 ohm load each channel. 03 Wave Form Asymmetrical Bi-Phasic Square Pulse 04 Voltage 0 to 50V (Load: 500 ohm) 05 Power source Four 1.5V AA batteries 06 Size 13.8cm(L) x 7.8cm(W) x 2.8cm(H) 07 Weight 425 grams with battery 08 Pulse Rate Adjustable, from 2 to 150 Hz, 1 Hz/step 09 Pulse Width Adjustable, from 50 to 300 microseconds, 10 µs/step 10 On Time Adjustable, 2~90 seconds , 1 Sec./ step 11 Off Time Adjustable, 0~90 seconds , 1 Sec./ step 12 Ramp Time Adjustable, 1~8 seconds, 1 Sec./ step, The "On" time will increase and decrease in the setting value. 13 Mode Five TENS Modes: B(Burst), N(Normal),M (Modulation), SD1( Strength Duration), SD2 Three EMS Modes:C(Constant) S (Synchronous), A(Alternate) 14 Burst Mode(B) Burst rate: Adjustable, 0.5 ~ 5Hz Pulse width adjustable, 50~300µs Frequency fixed = 100 Hz 15 Normal Mode(N) The pulse rate and pulse width are adjustable. It generates continuous stimulation based on the setting value. 16 Modulation Mode(M) Modulation mode is a combination of pulse rate and pulse width modulation. The pulse rate and width are automatically varied in a cycle pattern. The pulse width is decreased by 50% from its original setting in 0.5 second, then the pulse rate is decreased by 50% from its original setting in 0.5 second.Total cycle time is 1 second. In this mode, pulse rate(2-150Hz) and pulse width(50-300µs) are fully adjustable. 17 SD1 Mode The SD1(Strength-Duration) mode consists of automatic modulation intensity and pulse width in 40% range. The intensity is always increasing while the pulse width is decreasing and vice-versa. The intensity is decreased by 40% while the pulse width is increased by 40% in 5 seconds. In the next 5 seconds, the intensity is increased by 40% while the pulse width is decreased by 40%.Total cycle time is 10 seconds. Pulse rate ( 2~150Hz) and pulse width (50~300µs) are fully adjustable. 18 SD2 Mode The SD2(Strength-Duration) mode consists of automatic modulation intensity and pulse width in 70% range. The intensity is always increasing while the pulse width is decreasing and vice-versa. The intensity is decreased by 70% while the pulse width is increased by 70% in 5 seconds. In the next 5 seconds, the intensity is increased by 70% while the pulse width is decreased by 70%.Total cycle time is 10 seconds. Pulse rate( 2~150Hz) and pulse width (50~300µs) are fully adjustable. 19 Constant Mode (C) Constant stimulation based on setting value. Only pulse width, pulse rate and timer are adjustable in this mode. "Constant" is equal o the"Normal" mode of a TENS unit. 20 Synchronous Mode (S) Stimulation of both channels occurs synchronously. The "ON" time including "Ramp Up" and "Ramp Down" time. Therefore, the setting of ON Time should be no less than two times of the "Ramp" time in this mode. ON TIME≥Ramp up + Ramp down 21 Alternate Mode(A) The stimulation of the CH2 will occur after the 1st contraction of CH1 is completed. In this mode, the setting of ON Time should be no less than two times of the "Ramp" time. The OFF Time should be equal or more than the ON Time.  ON TIME ≥;Ramp up + Ramp down OFF TIME ≥IN TIME 22 Timer Two Adjustable timers, from 1 to 60 minutes or Continuous. Adjustable in 1 minute each step from 1 to 15 minutes, and 5 minutes each step from 15 to 60 minutes. Treatment time countdown automatically. 23 Patient Compliance Meter This unit can store 60 sets of operation records. Total recorded time is 999 hours. 24 Low Battery Indicator A low battery indicator will show up when the battery is low. 25 Operating Condition Temperature:0°~40° Relative Humidity: 30%~75% Atmosphere Pressure : 700Hpa~1060Hpa 26 Remark There may be up to a +/-5% tolerance of all parameters and +/-20% tolerance of amplitude & voltage. Features Precise Intensity Control There are 100 steps of intensity level controlled by press buttons from 1 to 100mA.  Press Button Control The power, intensity level and parameter are controlled by press buttons, which is easy for the users to adjust the settings. All of the buttons are protected by a swing door to avoid accidental touch.  Large Liquid Crystal Display A large LCD in 6.1 x 4.4 cm showing the intensity level, settings and treatment timer. The selected modes and parameters are readable.  Two Treatment Timers There are two individual timers controlling the output of CH1, CH2 & CH3, CH4. This function is ideal when two patients accept treatment with the same machine.  Treatment Time Countdown The output will shut off automatically when time is up.  Compliance Meter The unit can store 60 sets of record of operation.

Diameter: 19.6MM
Length: 110MM
With 2 rings PIGAIL connection

Specifications:
• 4 Point Fit & Ergonomic Design: Fit the neck in all directions, comfortable to wear and more satisfying; Ergonomic Design conforms to the curve of the human neck.
• Infrared Light Heating: Around 107.3 ℉Constant Temperature for Muscle Tension Relaxation
• Heating Temperance: From 100.4 ℉ to 107.3 ℉
• Light Weight Design: Small and light, convenient and easy to carry
• Product Details: Stainless steel electorate sheet, 3D Circular elastic arm and Micro-Surface Design
• Color Options: Pearl White
• Size: 14.2x 14.5 x 4.5cm
• Accessories: USB-C Charging Port Convenient and Quick Charging
 

Key Features:
• Pulse Massage: 5 Pulse Modes including Tapping, Scraping, Acupuncture, Kneading and Free Combination
• 16 Levels of Intensity Adjustment: Level 1-5 Comfortable for Neck Relaxation; Level 6-10 Moderate for Relieving Soreness; Level 11-16 Stimulus for Deep Massage.
• Working Duration Time: 15 minutes timer
• Quick Charging, Ultra-long Run Time: 1.5 Hours Charge & 1200mAh Lithium Battery℉
 

K3 Intelligent 4 point fit Neck Massager adopts with human body cervical physiological curvature of the popular type circular design. Using low-frequency pulse, infrared light heating, U-Shaped Design, Ergonomic design and 3D intelligent bonding technology to form a composite energy field to achieve tetras health care and fit the neck in all directions, comfortable to wear and more satisfying. During the working process, maintaining the correct physiological position to provide healthy and cosy therapy for the cervical spine. With Neck Massager, you can enjoy a more valuable, relaxed and happy multifunctional health care system at any time and anywhere.  

The Premier Stim Plus TENS/EMS is a fully digital battery operated pulse generator that sends electrical impulses to the nerves and underlying muscle groups. This unit is a combination stimulator of TENS and EMS which can be used for pain relief and muscle stimulation. The device is provided with two controllable output channels, each independent of the other. A pair of electrodes can be connected to each output channel. The intensity level and settings are controlled by press buttons.

Accessories:

1. Adhesive Electrodes 4 pcs
2. Electrodes Leads 2 pcs
3. 9V Battery  1 pcs
4. Blue Carrying Case 1 pcs
5. English Operation Manual 1 pcs
6. AC Power Cord 1 pcs
7. Tens Electrodes Placement Chart 1 pcs

 

 

 

	MECHANISM	TECHICAL DESCRIPTION
01	Channel	Dual, isolated between channels
02	Pulse Amplitude	Adjustable, 0-110 mA peak into 500 ohm load each channel.
03	Wave Form	Asymmetrical Bi-Phasic Square Pulse
04	Voltage	0 to 55V (Load: 500 ohm)
05	Power source	One 9 Volt Battery.
06	Size	11.8cm(L) x 6 cm(W) x 3.1cm(H)
07	Weight	157 grams with battery.
08	Pulse Rate	Adjustable, from 2 to 150 Hz, 1 Hz/step
09	Pulse Width	Adjustable, from 50 to 300 microseconds, 10 µs/step
10	On Time	Adjustable, 2~90 seconds , 1 Sec./ step
11	Off Time	Adjustable, 2~90 seconds , 1 Sec./ step
12	Ramp Time	Adjustable, 1~8 seconds, 1 Sec./ step, The "On"time will increase and decrease in the setting value.
13	Mode	Six TENS Modes: B(Burst), N(Normal),M (Modulation Rate & Width),S1( Modulation Width), S2 (Modulation Width) and P Three EMS Modes:C(Constant), S (Synchronous), A(Alternate)
14	Burst Mode	Burst rate: Adjustable, 0.5 ~ 5Hz Pulse width adjustable, 50~300 µs Frequency fixed = 100 Hz
15	Normal Mode	The pulse rate and pulse width are adjustable. It generates continuous stimulation based on the setting value.
16	Modulation Mode	Modulation mode is a combination of pulse rate and pulse width modulation. The pulse rate and width are automatically varied in a cycle pattern. The pulse width is decreased by 50% from its original setting in 0.5 second, then the pulse rate is decreased by 50% from its original setting in 0.5 second. Total cycle time is 1 second. In this mode, pulse rate(2-150Hz) and pulse width(50-300µs) are fully adjustable.
17	S1 Mode	Pulse width is automatically varied in a cyclic pattern over a nominal 10 second period. Pulse width decreases over a period of 4 seconds from the initial setting to a value 40% less. The narrower pulse width continues for 1 second. It then increases over a period of 4 seconds to its initial setting. The cycle is then repeated. Pulse rate and pulse width are fully adjustable.
18	S2 Mode	Pulse width is automatically varied in a cyclic pattern over a nominal 10 second period. Pulse width decreases over a period of 4 seconds from the initial setting to a value 70% less. The narrower pulse width continues for 1 second. It then increases over a period of 4 seconds to its initial setting. The cycle is then repeated. Pulse rate and pulse width are fully adjustable.
19	Constant Mode(C)	The pulse rate and pulse width are adjustable. It generates continuous stimulation is delivered .
20	Synchronous Mode(S)	Output from both channels occurs synchronously. The "ON" time includes "Ramp Up" and "Ramp Down" time. Therefore, the setting of ON Time should be no less than two times of the "Ramp" time in this mode.
21	Alternate Mode(A)	The stimulation of the CH2 will occur after Mode(A) the 1st contraction of CH1 is completed. In this mode, the setting of ON Time should be no less than two times of the "Ramp" time. The OFF Time should be equal to or greater than the ON Time. ON TIME ≥ Ramp up + Ramp down OFF TIME ≥ IN TIME
22	Mode P	The pre-set parameters of the 9 programs are as given below: Program Mode Pulse Rate Pulse Width Timer P1 Constant 80Hz 180µs Continue P2 Burst 100Hz (Burst Rate:2Hz) 180µs Continue P3 -70% P.W.Modulation 80Hz 50µs-180µs Continue P4 Mixed Frequency 15Hz in 3 Sec  /2Hz in 3 Sec 180µs Continue P5 Mixed Frequency 80Hz in 3 Sec / 2Hz in 3 Sec 180µs Continue P6 Constant 10Hz 180µs Continue P7 Constant 80Hz 60µs Continue P8 Constant 80Hz 180µs 30 Minutes P9 Burst 100Hz(Burst Rate:2Hz) 180µs 30 Minutes
23	Timer	Adjustable, from 5 to 60 minutes minutes and continue(C), 5 minutes each step.
24	Patient  Compliance Meter	This unit can store 60 sets of operation records. Total recorded time is 999 hours.
25	Low Battery Indicator	A low battery indicator will show up when the battery is low.
26	Operating Condition	Temperature:0°~40°C Relative Humidity: 30%~75% Atmosphere Pressure : 700Hpa~1060Hpa
27	Remark	There may be up to a +/-10% tolerance of all parameters and +/-20% tolerance of output amplitude & voltage.

Self-Adhesive Electrodes for:

- Transcutaneous Electrical Nerve Stimulator
- Electrical Muscle Stimulator
- Interferential Stimulator

This Electrode Refill Kit is to be used with the TENS Unit.

The refill packages come with everything you see here. We recommend replacing the electrode pads once they do not stick well or they have been used for more than 30 days. The Refill package contains one conductive cable set (lead wire) and 3 sets of re-usable, latex-free electrode pads (6 individual pads). 

The Refill Kit comes with:

•  2" x 2" re-usable electrode pads (3 packages of 2)
•  Conductive Cable (lead wire set)

The EM-2400 incontinence stimulator is a battery operated pulse generator that stimulates the muscles of the pelvic floor by means of a vaginal or rectal electrode. The unit has a single controllable channel which the electrode is connected to.

The stimulator has 5 preset programmes. The programme type and the intensity of stimulation are controlled by push buttons.